1. Home
  2. Tools
  3. Beam deflection calculator
Free tool  ·  Indicative  ·  Iron Axis engineering team

Beam deflection calculator: simply supported, cantilever and fixed beams

Find the maximum deflection, support reactions, shear force and bending moment of a beam under a uniform load and a point load. Choose simply supported, cantilever, fixed at both ends or propped cantilever, steel or concrete, check against L/360, L/240, span/250 or your own limit, and download the result as a printable report, a PDF or a CSV.

Engineering disclaimer. This free tool is for preliminary checks and education only. It uses simplified code methods and your inputs, and it is not a substitute for project design. Results must be verified by a qualified structural engineer responsible for the project. Verify every result against the current code edition, national annex, authority requirements and the project drawings before use. Iron Axis accepts no liability for decisions or designs based on these results. Read the full disclaimer.
Beam and supports
Unfactored dead + live along the full length.
Leave 0 for a uniform load only.
Measured from the left support.
Material and section
About the bending axis; from the steel section table or your own calculation.
Use 1.0 for steel. For cracked RC beams try 0.35–0.5, or Ie/Ig from ACI 318-19 24.2.3.5.
Deflection limit
— maximum deflection Simply supported
Step-by-step working

Indicative only, not a design. The results follow the methods and clauses set out below and depend on your inputs. Check them against the project drawings, specifications and the code edition and national annex adopted for the project.

How we calculate

1. Beam formulas

  • Linear-elastic Euler–Bernoulli beam theory with constant EI and small deflections; shear deformation is ignored. Deflection is downward positive and sagging moment positive.
  • The uniform load w acts over the whole length and the point load P at distance a from the left (fixed) end. Results for w and P are added (superposition) using the standard closed-form expressions tabulated in the AISC Steel Construction Manual beam diagrams [4]. The propped cantilever uses the cantilever solution minus the prop reaction RB = 3wL/8 + Pa²(3L − a)/(2L³).
  • We evaluate V(x), M(x) and δ(x) at 600 points plus the load point and refine the maximum deflection with a golden-section search, so the location of δmax under combined loads is found, not assumed at mid-span.

2. Stiffness

  • Steel: E = 200,000 MPa (AISC 360 [4]) or 210,000 MPa (EN 1993-1-1 3.2.6 [3]).
  • Concrete: Ec = 4700 √fc′ MPa for normalweight concrete (ACI 318-19 19.2.2.1(b) [1]) or Ecm = 22 [(fck + 8)/10]0.3 GPa (EN 1992-1-1 Table 3.1 [2]). Self-weight of a rectangular concrete section is added at 25 kN/m³ (EN 1991-1-1 Table A.1 [7]) when ticked.
  • I is either entered or b h³/12 for a solid rectangle, multiplied by your stiffness factor k to allow for cracking.

3. Limits, long-term deflection and reports

  • The allowable deflection is the span (or twice a cantilever length, per IBC Table 1604.3 [5], if ticked) divided by n. Options follow ACI 318-19 Table 24.2.2 [1], EN 1992-1-1 7.4.1(4) and (5) [2], IS 456:2000 23.2 [6] and IBC Table 1604.3 [5].
  • Long-term (concrete only): δ = δi (1 + λΔ × sustained share), with λΔ = ξ/(1 + 50ρ′) and ξ from Table 24.2.4.1.3 of ACI 318-19 [1].
  • The I needed is I × δ/δlim at the same loads. For a rectangle, the minimum depth h is found by bisection with the self-weight updated.
  • Print gives a one-document report with inputs, results, diagrams, working, date and disclaimer. Download PDF builds the report as a PDF in your browser; nothing is sent to us. Download CSV gives the results and V, M and δ at twentieths of the span for a spreadsheet.

What the calculator does

Deflection often governs the depth of beams and slabs long before strength does, especially for long spans, transfer structures and cantilevers. This calculator gives the elastic deflection of a single-span beam under a uniform load and a point load for the four support conditions we meet most, together with the reactions, the shear force and bending moment diagrams, and a check against the deflection limit you choose. It is the hand check we use to sanity-test finite element results before we rely on them.

Beam deflection formulas

The maximum values for the standard load cases, with w in N/mm (equal to kN/m), P in N, L in mm, E in MPa and I in mm⁴, so that δ comes out in mm [4]:

Maximum deflection and moment, single-span beams
Beam and loadMax deflectionMax moment
Simply supported, UDL5wL⁴/(384EI), mid-spanwL²/8
Simply supported, central point loadPL³/(48EI)PL/4
Cantilever, UDLwL⁴/(8EI), at the tipwL²/2 at the support
Cantilever, point load at the tipPL³/(3EI)PL at the support
Fixed both ends, UDLwL⁴/(384EI)wL²/12 at the supports, wL²/24 at mid-span
Fixed both ends, central point loadPL³/(192EI)PL/8 at the supports and mid-span
Propped cantilever, UDLwL⁴/(185EI), 0.4215L from the pinwL²/8 at the fixed end, 9wL²/128 in the span
Propped cantilever, central point loadPL³/(48√5 EI), 0.447L from the pin3PL/16 at the fixed end, 5PL/32 under the load

A fixed-ended beam deflects one fifth as much as a simply supported beam under a UDL, but only if the supports really are rigid. In buildings they rarely are, so we treat fixed-end results as a lower bound and look at the simply supported value as well.

Allowable deflection: L/360, L/240, span/250

Common deflection limits
Code and memberDeflection consideredLimit
ACI 318-19 Table 24.2.2, flat roofs not supporting damage-prone elementsImmediate, due to Lr, S and RL/180
ACI 318-19 Table 24.2.2, floors not supporting damage-prone elementsImmediate, due to LL/360
ACI 318-19 Table 24.2.2, supporting elements likely to be damagedAfter attachment of non-structural elements (long-term plus immediate from added live load)L/480
ACI 318-19 Table 24.2.2, supporting elements not likely to be damagedAs aboveL/240
EN 1992-1-1 7.4.1(4)Sag under quasi-permanent loadsspan/250
EN 1992-1-1 7.4.1(5)After construction, may damage adjacent partsspan/500
IS 456:2000 23.2(a) final, all loads; (b) after partitions and finishes(a) span/250; (b) span/350 or 20 mm
IBC 2021 Table 1604.3, floor membersLive load / dead + livel/360 / l/240

Sources: [1], [2], [6], [5]. For steel beams, EN 1993-1-1 7.2 leaves the limits to the national annex [3] and AISC 360 Chapter L treats deflection as a serviceability matter agreed for the project [4]; the IBC values are often used. For cantilevers, IBC Table 1604.3 takes l as twice the cantilever length [5], which the calculator does by default.

Concrete beams: cracking and long-term deflection

A reinforced concrete beam cracks under service load, so its stiffness falls well below the gross EI. ACI 318-19 uses an effective moment of inertia Ie between the cracked and gross values (24.2.3.5) and multiplies the sustained-load deflection by λΔ = ξ/(1 + 50ρ′) for creep and shrinkage (24.2.4.1) [1]. EN 1992-1-1 7.4.3 interpolates between the uncracked and fully cracked states and uses an effective modulus Ecm/(1 + φ) for creep [2]. The stiffness factor k and the long-term option in the calculator give a first estimate of these effects; a full check needs the reinforcement, cracking moment and load history. Our guide to long-term deflection to Eurocode 2 and ACI sets out the full method.

Post-tensioned beams and slabs

Post-tensioning controls deflection by balancing part of the load. A parabolic tendon with effective force Pe and drape e applies an upward load of about 8Pe·e/L², so for a first look you can enter the net service load (applied load minus the balanced load) and gross stiffness, since a well-balanced PT member is usually uncracked under service load. Long-span PT beams and transfer beams then need the full analysis with secondary effects and the load history, which is the work we do on PT transfer slabs and beams and in RAM Concept load-history deflection runs.

Worked examples

  • Steel beam. Simply supported, L = 6 m, w = 20 kN/m, E = 200 GPa, I = 100 × 10⁶ mm⁴: δ = 5 × 20 × 6000⁴/(384 × 200,000 × 100 × 10⁶) = 16.9 mm against L/360 = 16.7 mm, so it fails by about 1%. The calculator reports I needed = 101.3 × 10⁶ mm⁴.
  • RC beam. Simply supported 300 × 600 mm, L = 6 m, fc′ = 30 MPa (Ec = 25,743 MPa), w = 20 kN/m plus 4.5 kN/m self-weight, k = 0.5: δi = 5.9 mm. With ξ = 2.0, ρ′ = 0.5% (λΔ = 1.6) and 60% sustained load, δ = 5.9 × (1 + 1.6 × 0.6) = 11.7 mm against L/240 = 25 mm, 47% of the limit.
  • Steel cantilever. L = 2.5 m, w = 15 kN/m and P = 10 kN at the tip, I = 60 × 10⁶ mm⁴: δ = 6.1 + 4.3 = 10.4 mm; with l = 2 × 2.5 m, L/180 = 27.8 mm.

Sizing a slab? Try the PT slab thickness calculator, the RC vs PT slab calculator or the punching shear calculator. For vibration rather than deflection, see floor vibration in PT slabs.

References

The codes and references the calculator follows, consulted on 17 November 2026. Clause numbers are given so you can check each step; always use the edition and national annex adopted for your project.

  1. American Concrete Institute: ACI 318-19 Building Code Requirements for Structural Concrete and Commentary: 19.2.2.1 (modulus of elasticity Ec), Table 24.2.2 (maximum permissible calculated deflections), 24.2.3.5 (effective moment of inertia Ie) and 24.2.4.1 (time-dependent deflection, λΔ and Table 24.2.4.1.3)
  2. CEN: EN 1992-1-1:2004+A1:2014 Eurocode 2: Design of concrete structures, Part 1-1: Table 3.1 (Ecm), 7.4.1(4) and (5) (deflection limits) and 7.4.3 (calculation of deflection)
  3. CEN: EN 1993-1-1:2005 Eurocode 3: Design of steel structures, Part 1-1: 3.2.6 (E = 210,000 N/mm²) and 7.2 (vertical deflections, limits to be agreed or given in the national annex)
  4. American Institute of Steel Construction: ANSI/AISC 360-22 Specification for Structural Steel Buildings (E = 200,000 MPa; Chapter L, design for serviceability) and the AISC Steel Construction Manual beam diagrams and formulas (Table 3-23)
  5. International Code Council: International Building Code 2021, Table 1604.3 Deflection limits, including the footnote taking l as twice the length for cantilever members
  6. Bureau of Indian Standards: IS 456:2000 Plain and Reinforced Concrete, Code of Practice: 23.2 (control of deflection: span/250 final; span/350 or 20 mm after partitions and finishes)
  7. CEN: EN 1991-1-1:2002 Eurocode 1: Actions on structures, Part 1-1: Table A.1 (reinforced concrete 25 kN/m³)

Part of our free engineering tools and design guides. Codes are referred to by clause where we are confident of the reference; always check the edition and national annex adopted for your project.

S-591 FAQ

Questions we are asked about this.

How do you calculate beam deflection?

Pick the support condition and load case, then use the elastic formula, for example δ = 5wL⁴/(384EI) for a simply supported beam with a uniform load. E is the modulus of elasticity of the material and I the second moment of area of the section. For combined loads, add the deflection curves and find the maximum along the span, which is what this calculator does.

What is the deflection of a simply supported beam with a uniformly distributed load?

δmax = 5wL⁴/(384EI) at mid-span. For a 6 m steel beam with w = 20 kN/m and I = 100 × 10⁶ mm⁴ (E = 200 GPa) that is 16.9 mm, just over L/360 = 16.7 mm.

What is the deflection formula for a cantilever beam?

For a uniform load, δtip = wL⁴/(8EI). For a point load at the tip, δtip = PL³/(3EI); for a point load at distance a from the support, δtip = Pa²(3L − a)/(6EI). The fixed-end moment is wL²/2 or Pa.

What is the deflection of a beam fixed at both ends?

Under a uniform load, δmax = wL⁴/(384EI), one fifth of the simply supported value, with end moments wL²/12. Under a central point load, δmax = PL³/(192EI) with end moments PL/8. Real supports are seldom fully fixed, so treat this as a lower bound.

What is the allowable deflection for beams: L/360, L/240 or span/250?

It depends on the code and what the beam supports. ACI 318-19 Table 24.2.2 gives L/360 for immediate live-load deflection of floors and L/480 or L/240 for deflection after non-structural elements are attached. EN 1992-1-1 7.4.1 gives span/250 under quasi-permanent loads and span/500 after construction, IS 456:2000 23.2 gives span/250 and span/350 or 20 mm, and IBC Table 1604.3 gives l/360 for live and l/240 for dead plus live load on floors.

What deflection limit applies to a cantilever?

IBC Table 1604.3 takes l as twice the cantilever length, so L/360 becomes 2L/360. ACI 318-19 and EN 1992-1-1 express limits per span; many engineers apply the same twice-length rule to cantilevers. The calculator uses twice the length by default and lets you switch it off.

Can I use it for reinforced concrete or post-tensioned beams?

Yes, for a first estimate. Choose a concrete option for Ec, reduce the stiffness factor for cracking (about 0.35 to 0.5 for RC), and add the ACI 318-19 long-term multiplier. For PT members, enter the net load after the tendon balancing load. A final check needs the effective inertia, creep, shrinkage and load history.

Can I print or save the results?

Yes. Print gives a clean report with the inputs, results, diagrams, working, date and disclaimer. Download PDF creates the report as a PDF in your browser, and Download CSV gives the results with V, M and δ along the span for a spreadsheet. Nothing is uploaded to our server.

S-901 Contact

Send the drawings. Get an answer from our engineers.

WhatsApp or email the architectural or structural set, the location and what you need. The reply comes from the engineers who will do the work, with a proposed scope and programme.

Office
Al Warqa 1, Dubai, UAE
Hours
Sunday – Thursday, 09:00 – 18:00 GST