1. Home
  2. Resources
  3. PT slab vibration
Technical note  ·  Iron Axis engineering team

Floor vibration in post-tensioned slabs

Thinner, longer-span PT floors are lighter and more flexible than the slabs they replace, so footfall vibration deserves a check. How walking excites a floor, which guides are used, and what actually improves the response.

Design codes
ACI 318 · Eurocode 2 · PTI
Software
RAM Concept · AutoCAD · Revit

Post-tensioning lets a slab span further and be thinner than an equivalent reinforced concrete slab. That is the point of using it, but it also means less stiffness and less mass per square metre, and both lower the natural frequency of the floor. Most PT floors in offices and residential buildings perform well under footfall. The ones that do not are usually long-span, slender floors with little fit-out, or floors under sensitive uses such as hospitals, laboratories and high-specification offices.

Prestress itself does not make a floor much stiffer. Its main benefit for vibration is indirect: a slab designed to stay largely uncracked under service loads keeps close to its gross-section stiffness, so the stiffness used in a vibration analysis is easier to justify.

How walking excites a floor

A person walking applies a repeating force at the pace frequency, typically about 1.5 to 2.5 steps per second, together with harmonics at two, three and four times that frequency. Two kinds of response follow:

  • Resonant response. If a natural frequency of the floor is close to one of the first few harmonics of walking, the response can build up step after step. This governs floors with low fundamental frequencies, roughly below four times the highest pace frequency considered.
  • Impulsive (transient) response. On stiffer floors with higher frequencies, each footstep produces a short decaying response that dies away before the next. The response then depends mainly on the floor's stiffness and modal mass rather than on resonance.

The guides draw the boundary between "low-frequency" and "high-frequency" floors slightly differently. A figure of around 10 Hz is commonly used, and some guidance places the change to a fully impulsive response nearer 12 to 15 Hz. Floors well above the boundary are checked for impulsive response; floors below it need a resonant check, and floors close to it are best checked for both.

Estimating the natural frequency

For a first estimate, the fundamental frequency of a floor panel can be related to its instantaneous deflection under the mass that vibrates with it:

fn ≈ 18 / √δ   (fn in Hz, δ in mm)

where δ is the short-term elastic deflection under self-weight, superimposed dead load and a realistic part of the imposed load, not the full design live load. This comes from the single-degree-of-freedom relationship with an allowance for distributed mass. It is a screening tool only. Flat slabs are continuous in two directions, adjacent panels vibrate together, and the critical mode is often not the one a single-panel estimate assumes. A finite element modal analysis is the normal way to check a PT flat slab.

Three inputs make the biggest difference to the result:

  • Dynamic modulus. Concrete is stiffer under the small, fast strains of vibration than under static load. Guides and software apply a factor to the static modulus for this; RAM Concept's default dynamic modulus factor is 1.2.
  • Mass. Include self-weight, superimposed dead load and only the small fraction of imposed load that is realistically present. Overestimating mass lowers the predicted frequency, which can push a floor into the resonant range on paper.
  • Supports. Column and wall stiffness, and whether edges are supported by facades or beams, change the mode shapes. Model them as for the static analysis.

The design guides used in practice

Common footfall vibration guidance
GuideScope and approach
AISC Design Guide 11, Vibrations of Steel-Framed Structural Systems Due to Human ActivityWritten for steel-framed floors. Its walking criterion compares a predicted peak acceleration with tolerance limits, such as 0.5% g for offices and residences. It is sometimes used as a quick screening check for concrete floors, but its simplified formulas are calibrated for steel framing.
CCIP-016, A Design Guide for Footfall Induced Vibration of Structures (The Concrete Centre)Written with concrete floors in mind and includes a post-tensioned flat slab among its examples. Gives simplified and modal methods for low- and high-frequency floors, expressed as a response factor.
SCI P354, Design of Floors for Vibration: A New Approach (Steel Construction Institute)Developed for steel and composite floors, with a general modal method and response-factor criteria that are also applied to other floor types.

The project specification or client brief should name the guide and the acceptance criteria. If it does not, agree them before design starts; changing the criterion late is far more expensive than designing to it.

Response factor and acceptance criteria

The response factor R expresses the frequency-weighted acceleration as a multiple of a base value close to the threshold of human perception, so R = 1 is barely perceptible and R = 8 is eight times that level. CCIP-016 suggests R = 8 is usually satisfactory for general offices where footfall vibration is intermittent, with a lower target, by up to a factor of two, for premium open-plan offices, busy corridors near mid-span and similar cases. For residential floors it recommends values twice the BS 6472 levels for continuous vibration, which gives a daytime target of about R = 4. Operating theatres and vibration-sensitive equipment need much lower values set by the equipment or the healthcare specification.

These criteria are about the probability of adverse comment, not structural safety. A floor that exceeds the target is not unsafe, but occupants may notice and complain.

Damping

Damping in concrete floors is low, a few percent of critical at most. The value assumed has a direct effect on the resonant response, so it should match the fit-out that will actually be present:

  • bare structural slabs, as during construction or in shell-and-core handover, sit at the low end, around 1 to 1.5%;
  • fitted-out floors with ceilings, services, raised floors and furniture are typically taken at around 3%;
  • floors with full-height partitions can reach around 4.5%, but movable and part-height partitions should not be relied on.

The RAM Concept help gives a normal range of 0.01 to 0.04 for concrete buildings. If the tenant fit-out is unknown, design for the lower end.

Practical ways to improve a floor

  • Increase depth. Stiffness grows with the cube of thickness while mass grows only linearly, so a modest increase in slab depth raises the frequency and reduces the response. Drop panels and column heads help locally.
  • Shorten the critical span or add a band beam. Long single spans, cantilevers and transfer bays are where problems concentrate.
  • Stiffen free edges. Edge beams or upstands along slab edges and around large openings and atria reduce edge-mode response.
  • Plan the layout. Keep heavily used corridors and sensitive rooms away from mid-span of the most flexible panels where the architecture allows.
  • Use the mass you have. Screeds and raised floors add mass that reduces resonant response, provided the extra load is allowed for in the static design.

Adding prestress does not materially change the natural frequency. It can still help by keeping the slab uncracked, which protects the stiffness assumed in the analysis.

Footfall analysis in RAM Concept

RAM Concept includes a vibration analysis that calculates natural frequencies and mode shapes, then the resonant and impulsive footfall response across the floor. The main inputs sit in the calculation options: the number of modes, the dynamic concrete modulus factor, the range of footstep frequencies, the damping ratio, the weight of the walker and the response types to calculate. The stiffness can be taken from the linear elastic model or from a load history step if cracking needs to be reflected; see our guide to load history deflections. Results are plotted as response factor contours, which makes it easy to see where the floor needs attention. Our wider RAM Concept tips apply here too: the vibration answer is only as good as the supports, mesh and mass in the model.

When we check vibration

We include a footfall check in the design or review when spans are long for the slab depth, when the floor is light or has large cantilevers, when the occupancy is sensitive (healthcare, laboratories, premium offices, open-plan floors with long corridors), when the brief names a vibration criterion, and when a value-engineering proposal reduces slab depth. Rhythmic activities such as gyms and dance studios are a separate check with different loading and criteria.

Talk to us about your PT floor. Our team checks footfall vibration as part of PT slab design and review. Send us the layout for a PT design review, check a thinner scheme with a PT design optimisation, discuss a full post-tension design package, read about our post-tension design in the UAE, or contact our engineers.

Related PT design guides: precompression and balanced load, transfer and service stress checks.

Part of our PT technical series. Codes are referred to by clause where we are confident of the reference; always check the edition and national annex adopted for your project.

S-212 FAQ

Questions we are asked about this.

What natural frequency should a PT slab have?

There is no single target. What matters is the response to walking. Floors with a fundamental frequency well above roughly 10 Hz respond mainly impulsively and usually perform well; floors below this need a resonant response check against the agreed response factor or acceleration limit.

Does post-tensioning improve floor vibration?

Mostly indirectly. Prestress does not materially raise the natural frequency, but it keeps the slab largely uncracked, which preserves stiffness. Because PT slabs are usually thinner and span further, they can be more lively than the RC slabs they replace, so a check is worthwhile on long spans.

What response factor is acceptable for an office floor?

CCIP-016 suggests R = 8 is usually satisfactory for general offices with intermittent footfall, with a lower target, by up to a factor of two, for premium open-plan offices and busy corridors near mid-span. The client brief or specification should confirm the criterion.

What damping should be used for a concrete floor?

Damping should match the expected fit-out: around 1 to 1.5% for bare slabs, around 3% for fitted-out floors, and up to around 4.5% where full-height partitions are reliably present. If the fit-out is unknown, use the lower end.

Can RAM Concept check footfall vibration?

Yes. RAM Concept calculates natural frequencies and mode shapes and the resonant and impulsive footfall response, and plots response factor contours. The inputs include the dynamic modulus factor, footstep frequency range, damping and walker weight.

Can you check vibration on our PT slab design?

Yes. We include footfall vibration checks in PT slab design and review, and we can assess the effect of slab thickness changes proposed in value engineering.

S-901 Contact

Send the drawings. Get an answer from our engineers.

WhatsApp or email the architectural or structural set, the location and what you need. The reply comes from the engineers who will do the work, with a proposed scope and programme.

Office
Al Warqa 1, Dubai, UAE
Hours
Sunday – Thursday, 09:00 – 18:00 GST