Continuous beam calculator: moments, shears and reactions
Analyse a continuous beam of 2 to 5 spans with uniform and point loads. Get support and span moments, reactions, shear and bending moment diagrams and the service deflection, with live load patterned span by span for the worst case, and follow the slope-deflection working step by step.
Step-by-step working
Indicative only. Elastic analysis of an idealised prismatic beam; not a member design.
How we calculate
1. Slope-deflection analysis
- Each span has fixed-end moments from its loads: wL²/12 for a uniform load and Pab²/L², Pa²b/L² for a point load [1].
- Joint rotations are the unknowns. Each span contributes the stiffness 4EI/L at its near end and 2EI/L at the far end; the equations Σ M = 0 at each free joint are solved directly, then end moments M = FEM + (2EI/L)(2θnear + θfar). Fixed ends have θ = 0.
- Reactions and shears come from statics of each span with its end moments; the bending moment between supports is the free (simply supported) moment plus the line joining the end moments.
2. Live load patterns
- With patterning on, the factored dead load is applied to all spans and the factored live load to every combination of spans (up to 2⁵ = 32 cases). The envelope keeps the largest and smallest moment, shear and reaction at each point. This covers the ACI 318-19 §6.4.2 arrangements and the EN 1992-1-1 §5.1.3 simplified arrangements for continuous beams [2][3].
3. Deflection
- Service deflection uses unfactored dead plus live load on all spans and the E and I you enter, by integrating the moment diagram of each span with the end rotations from the analysis. For concrete, enter a cracked or effective I, or the result will be too small.
Why continuous beams need their own calculator
A beam that runs over several supports carries load differently from a set of simple spans. The supports attract hogging moments, the span moments drop and the interior reactions rise. For two equal spans under a uniform load w, the interior support moment is wL²/8 and the interior reaction 1.25 wL, compared with 0.5 wL from each simple span. Simple-span formulas therefore underestimate both the top steel and the load on the interior column.
Worked check: three equal spans
For three equal spans of 6 m with a uniform factored load of 40 kN/m on all spans, the classic coefficients give:
- Interior support moments −0.100 wL² = −144 kN·m; end span moment +0.080 wL² = 115.2 kN·m; middle span +0.025 wL² = 36 kN·m.
- Reactions 0.40 wL = 96 kN at the ends and 1.10 wL = 264 kN at the interior supports.
The calculator reproduces these values with patterning turned off. Turn it on with 1.2 × 20 dead and 1.6 × 10 live and the support moment rises to about −154 kN·m and the end span moment to 127 kN·m, because live load on alternate or adjacent spans is worse than load on all spans.
Coefficients or analysis?
ACI 318-19 §6.5 allows approximate moment coefficients for roughly equal spans (the longer of adjacent spans not more than 1.2 times the shorter), uniform loads and L/D ≤ 3 [2]. When spans differ, there are point loads, or the live load is large, an analysis like this one is needed. Our one-way slab calculator uses the coefficients for slabs where they apply.
Limitations
- Supports are rigid and the beam is prismatic: the same E and I in every span. Haunches, flexible supports and column stiffness are not modelled.
- Moments are elastic, at support centrelines. Codes allow limited redistribution and design at the face of support; we do not apply either.
- For post-tensioned beams, secondary moments from prestress need a separate analysis. See our transfer slab and beam design service.
References
The codes and texts the calculator follows, consulted on 19 November 2026. Always use the edition and national annex you will actually rely on.
- R. C. Hibbeler: Structural Analysis: slope-deflection equations and fixed-end moments (any recent edition)
- ACI: ACI 318-19 Building Code Requirements for Structural Concrete: §6.4 arrangement of live load and §6.5 simplified method of analysis
- CEN: EN 1992-1-1:2004 Eurocode 2: §5.1.3 load cases and combinations (alternate and adjacent spans loaded)
Part of our free engineering tools and design guides. Results are for preliminary design and checking, and must be verified by a qualified structural engineer responsible for the project. Clauses are referred to where we are confident of the reference; always check the edition and national annex adopted for your project.
Questions we are asked about this.
How do you calculate moments in a continuous beam?
Use an indeterminate method such as slope-deflection or moment distribution: find fixed-end moments, solve for the joint rotations, then the end moments. For equal spans with a uniform load you can use tabulated coefficients, for example −0.125 wL² at the middle support of a two-span beam.
What is the support moment of a two-span continuous beam?
For two equal spans with a uniform load w on both spans, M = −wL²/8 at the middle support, the same as a propped cantilever. The end reactions are 0.375 wL and the middle reaction 1.25 wL.
Why pattern the live load?
Maximum span moments occur with live load on alternate spans, and maximum support moments with live load on the two spans next to the support. ACI 318-19 §6.4.2 and EN 1992-1-1 §5.1.3 require these arrangements.
Can I use this calculator for steel beams?
Yes for the analysis: enter E = 200 GPa and the section Ix. Then check the member to AISC 360 or EN 1993-1-1, including lateral-torsional buckling at the hogging regions.
What I should I use for a concrete beam?
The gross I overstates stiffness once the beam cracks. For deflection, an effective I of roughly 0.35 to 0.5 Ig is common for preliminary checks; the moment distribution is less sensitive if all spans use the same ratio.
Does it include the self-weight?
No. Add the self-weight of the beam to the dead load per metre, for example 0.3 × 0.6 × 25 = 4.5 kN/m for a 300 × 600 concrete beam.
Send the drawings. Get an answer from our engineers.
WhatsApp or email the architectural or structural set, the location and what you need. The reply comes from the engineers who will do the work, with a proposed scope and programme.
- +971 52 118 2569
- Telephone
- +971 52 118 2569
- Office
- Al Warqa 1, Dubai, UAE
- Hours
- Sunday – Thursday, 09:00 – 18:00 GST
