Moment of inertia calculator for I-beam, T, box, tube and more
Find the second moment of area I, elastic modulus S, plastic modulus Z and radius of gyration of common structural sections. See the centroid, the parallel-axis working part by part and a sketch with the axes, then print it or download a PDF or CSV.
Step-by-step working
Indicative only. Properties are for the idealised shape entered, without root fillets or corner radii.
How we calculate
1. Rectangles and the parallel-axis theorem
- I, T, channel, angle and box sections are split into non-overlapping rectangles (flanges and web). For each part Ix,i = b h³/12 + A dy², where dy is the distance from the part’s centroid to the section centroid; the same for Iy [1].
- Centroid: ȳ = Σ A y / Σ A, measured from the bottom-left corner of the bounding box.
2. Section moduli and radius of gyration
- Elastic modulus S = I / c to each extreme fibre, so unsymmetric sections (T, channel about y, angle) have two values. r = √(I/A).
- Plastic modulus Z: the equal-area axis is found by bisection, then Z = Σ |A × distance| of each part to that axis [2]. Circles use Z = (D³ − d³)/6.
3. Angles
- Ix, Iy and the product of inertia Ixy are found about axes parallel to the legs; principal values Iu,v = (Ix + Iy)/2 ± √(((Ix − Iy)/2)² + Ixy²).
What the moment of inertia tells you
The second moment of area I measures how a cross-section resists bending. Deflection is proportional to 1/(EI), and bending stress is M/S where S = I/c. Doubling the depth of a rectangle multiplies I by eight, which is why deep sections are so efficient. For example, a 300 × 600 mm rectangle has Ix = 300 × 600³/12 = 5,400 × 10⁶ mm⁴; turned on its side it has only 1,350 × 10⁶ mm⁴.
I-beam moment of inertia: a worked example
Take an I section 300 mm deep with 150 × 10 mm flanges and a 6 mm web, ignoring the root fillets:
- Ix = (150 × 300³ − 144 × 280³)/12 = (4,050 − 3,161.1) × 10⁶ / 12 = 74.08 × 10⁶ mm⁴.
- Sx = Ix / 150 = 493.8 × 10³ mm³.
- Zx = 150 × 10 × 290 + 6 × 280²/4 = 552.6 × 10³ mm³, a shape factor of about 1.12.
Rolled sections have fillets at the web-to-flange junction, so published tables give slightly higher A and I than a square-cornered model. Use the producer’s table for design and this calculator for built-up, welded or unusual sections and for checking.
Elastic or plastic modulus?
Use S for first-yield or allowable-stress checks and Z for plastic bending resistance, which only compact (AISC 360) or Class 1 and 2 (EN 1993-1-1) sections can reach [2][3]. Thin flanges or webs buckle first, and a section check, not just its properties, decides the resistance.
Using I in other calculations
Take I from here into our beam deflection calculator or continuous beam calculator. For concrete members, the gross I of the rectangle overstates the stiffness after cracking; ACI 318-19 §24.2.3.5 uses an effective moment of inertia instead.
References
The codes and texts the calculator follows, consulted on 19 November 2026. Always use the edition and national annex you will actually rely on.
- R. C. Hibbeler: Mechanics of Materials: properties of areas, parallel-axis theorem and product of inertia (any recent edition)
- AISC: ANSI/AISC 360-22 Specification for Structural Steel Buildings: §F2 (Mp = Fy Zx) and Table B4.1b (compactness)
- CEN: EN 1993-1-1:2005 Eurocode 3: §5.5 classification of cross-sections and §6.2.5 bending resistance (Wpl, Wel)
Part of our free engineering tools and design guides. Results are for preliminary design and checking, and must be verified by a qualified structural engineer responsible for the project. Clauses are referred to where we are confident of the reference; always check the edition and national annex adopted for your project.
Questions we are asked about this.
How do you calculate the moment of inertia of an I-beam?
For a symmetric I section without fillets, Ix = [b h³ − (b − tw)(h − 2tf)³]/12. For example a 300 × 150 section with 10 mm flanges and a 6 mm web has Ix = 74.1 × 10⁶ mm⁴ (7,408 cm⁴).
What is the moment of inertia of a rectangle?
About its centroidal axis parallel to the width, I = b h³/12. A 300 mm wide, 600 mm deep beam has I = 5,400 × 10⁶ mm⁴.
What is the difference between elastic and plastic section modulus?
The elastic modulus S = I/c gives the moment at first yield (M = Fy S). The plastic modulus Z gives the fully plastic moment (Mp = Fy Z). Z/S is the shape factor: 1.5 for a rectangle and about 1.1 to 1.2 for I sections.
How do I convert mm⁴ to cm⁴ or in⁴?
1 cm⁴ = 10⁴ mm⁴ and 1 in⁴ = 416,231 mm⁴. So 74.08 × 10⁶ mm⁴ = 7,408 cm⁴ = 178 in⁴.
Why do my results differ from the steel section table?
Rolled sections have root fillets (and hollow sections have corner radii) that this calculator ignores. The table values are slightly higher and should be used for design.
What is the radius of gyration used for?
r = √(I/A) is used for column slenderness (kL/r) and lateral-torsional buckling. The smaller value, usually ry, governs the buckling of an unbraced member.
Send the drawings. Get an answer from our engineers.
WhatsApp or email the architectural or structural set, the location and what you need. The reply comes from the engineers who will do the work, with a proposed scope and programme.
- +971 52 118 2569
- Telephone
- +971 52 118 2569
- Office
- Al Warqa 1, Dubai, UAE
- Hours
- Sunday – Thursday, 09:00 – 18:00 GST
