1. Home
  2. Tools
  3. Development length calculator (ACI 318)
Free tool  ·  Indicative  ·  Iron Axis engineering team

Development length calculator to ACI 318-19

Work out the tension development length of deformed bars to ACI 318-19 in SI units: the simplified Table 25.4.2.3 and the detailed equation 25.4.2.4a with ψt, ψe, ψs, ψg, λ, cb and Ktr, standard hooks to 25.4.3, and Class A and B tension laps. Every factor is shown, with a printable report, a PDF and a CSV.

Engineering disclaimer. This free tool is for preliminary checks and education only. It uses simplified code methods and your inputs, and it is not a substitute for project design. Results must be verified by a qualified structural engineer responsible for the project. Verify every result against the current code edition, national annex, authority requirements and the project drawings before use. Iron Axis accepts no liability for decisions or designs based on these results. Read the full disclaimer.
Bar and materials
Grade 420 = 420 MPa. ψg rises for Grades 550 and 690.
Cylinder strength: C30/37 is 30 MPa.
Cover, spacing and confinement
Hooks and excess reinforcement
Leave at 1.0 unless the reduction is permitted.
— mm straight development length ld 16 mm · Table 25.4.2.3
Step-by-step working

Indicative only, not a design. The results follow the methods and clauses set out below and depend on your inputs. Check them against the project drawings, specifications and the code edition and national annex adopted for the project.

How we calculate

1. Factors (ACI 318-19 Table 25.4.2.5)

  • λ = 0.75 for lightweight and 1.0 for normalweight concrete. ψg = 1.0 for Grade 280 and 420, 1.15 for Grade 550 and 1.3 for Grade 690; for an fy between grades we use the next grade up. ψe = 1.5 for epoxy-coated bars with cover below 3db or clear spacing below 6db, 1.2 for other epoxy-coated bars and 1.0 for uncoated or galvanized bars. ψs = 0.8 for No. 19 and smaller bars and 1.0 for No. 22 and larger. ψt = 1.3 for bars with more than 300 mm of fresh concrete below them, otherwise 1.0. The product ψtψe need not exceed 1.7 [1].
  • √fc′ is limited to 8.3 MPa (25.4.1.4) [1].
  • Bar diameters for the No. sizes are the nominal values of the ASTM A615M soft-metric designations [2]. A 20 mm bar falls between No. 19 (19.1 mm) and No. 22 (22.2 mm). We put it in the larger group, which gives the longer length.

2. Straight bars in tension (25.4.2)

  • Simplified, Table 25.4.2.3: ld = fy ψt ψe ψg / (C λ √fc′) × db, with C = 2.1 (No. 19 and smaller) or 1.7 (No. 22 and larger) when the clear spacing is at least db, the clear cover at least db and the stirrups or ties along ld at least the code minimum, or when the clear spacing is at least 2db and the cover at least db; otherwise C = 1.4 or 1.1 [1].
  • Detailed, eq. 25.4.2.4a: ld = fy / (1.1 λ √fc′) × ψt ψe ψs ψg / [(cb + Ktr)/db] × db, where cb is the smaller of the cover to the bar centre and half the centre-to-centre spacing, Ktr = 40 Atr/(s n) or 0, and (cb + Ktr)/db is limited to 2.5 [1].
  • ld is multiplied by As,required/As,provided where 25.4.10 permits, and is not less than 300 mm [1].

3. Standard hooks in tension (25.4.3)

  • ldh = fy ψe ψr ψo ψc / (23 λ √fc′) × db1.5, not less than 8db or 150 mm, with ψe = 1.2 for epoxy-coated bars, ψr = 1.0 where Ath ≥ 0.4 Ahs or the hooked bars are spaced at 6db or more (otherwise 1.6), ψo = 1.0 for hooks ending inside a column core with side cover of 65 mm or more, or with side cover of 6db or more (otherwise 1.25), and ψc = fc′/105 + 0.6 below 40 MPa and 1.0 above. For bars larger than No. 36, ψr = 1.6 and ψo = 1.25 [1].
  • Hook geometry must follow Table 25.3.1 [1].

4. Tension lap splices (25.5.2)

  • Class A: 1.0 ld, where As,provided/As,required is at least 2 over the splice and no more than half of the bars are spliced within the lap. Class B: 1.3 ld in all other cases. Both are at least 300 mm, and ld is taken without the 25.4.10 reduction [1].
  • Print gives a one-document report with inputs, results, working, date and disclaimer. Download PDF builds the same report as a PDF in your browser; nothing is sent to us. Download CSV gives the numbers for a spreadsheet.

What the calculator does

Development length is the embedment a bar needs to reach its yield stress without pulling out or splitting the concrete. It sets anchorage into supports, the length of bars past the point where they are no longer needed, and, through Chapter 25, the length of lap splices. It also matters in post-tensioned slabs, where the bonded reinforcement over columns, at slab edges and around openings has to be properly developed.

This calculator works through ACI 318-19 [1] in SI units and shows every factor so the result can be checked against the code. It gives both straight-bar methods side by side, the standard hook length and the Class A and Class B lap lengths, so you can see how much the detailed method saves.

Simplified table or detailed equation?

  • Table 25.4.2.3 is quick and needs only the bar size, the cover and spacing case and the factors. It is conservative because it assumes a modest confinement term.
  • Eq. 25.4.2.4a uses the actual cover and spacing through cb, and the transverse reinforcement through Ktr. With good cover and spacing the term (cb + Ktr)/db reaches its 2.5 limit and the length can be well below the table value.

Either method is permitted. Using the detailed equation means checking the cover, spacing and transverse steel on the drawings for each case.

How to use it

  1. Choose the bar size, the yield strength and the specified cylinder strength fc′. For a C30/37 concrete, fc′ is 30 MPa.
  2. Set the concrete type and coating, and tick the top-bar box for horizontal bars with more than 300 mm of concrete cast below them, such as top bars in deep beams and thick slabs.
  3. Enter the clear cover and the clear spacing between the bars being developed, and whether the stirrups or ties along the bar are at least the code minimum.
  4. Choose the method. For the detailed equation, take Ktr as 0 or enter the transverse steel.
  5. For hooks, tick the confinement and location conditions only where the detail meets them.
  6. Read ld, ldh and the lap lengths, then use Print, Download PDF or Download CSV.

Assumptions and limitations

  • Deformed bars in tension only. Compression development (25.4.9), headed and mechanically anchored bars (25.4.4 and 25.4.5), bundled bars and welded wire reinforcement are not covered.
  • Bars and anchorages in special seismic systems have additional requirements in Chapter 18 that are not checked here.
  • The As,required/As,provided reduction is not allowed in several cases listed in 25.4.10.2. Leave the ratio at 1.0 unless you have checked that it applies.
  • Results are rounded up to the next millimetre. Round up again to your detailing increment.

Working to Eurocode 2 instead? Use our lap length calculator to EN 1992-1-1. For bar weights, use the rebar weight calculator, and for reinforcement in PT anchorage zones, read our guide to PT anchorage zone bursting reinforcement.

References

The codes and standards the calculator follows, consulted on 15 November 2026. Clause numbers are given so you can check each step; always use the edition and national annex adopted for your project.

  1. American Concrete Institute: ACI 318-19 Building Code Requirements for Structural Concrete and Commentary: 19.2.4 (lightweight factor λ), 25.3 (standard hooks), 25.4.1 to 25.4.3 (development of deformed bars and standard hooks in tension, Tables 25.4.2.3, 25.4.2.5 and 25.4.3.2), 25.4.10 (excess reinforcement) and 25.5.2 (tension lap splices)
  2. ASTM International: ASTM A615/A615M Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement, Table 1 (bar designations, nominal weights, diameters and areas)

Part of our free engineering tools and design guides. Codes are referred to by clause where we are confident of the reference; always check the edition and national annex adopted for your project.

S-571 FAQ

Questions we are asked about this.

What is the development length of a 16 mm bar to ACI 318-19?

With fy = 420 MPa, fc′ = 30 MPa, normalweight concrete, uncoated bottom bars and adequate cover and spacing, Table 25.4.2.3 gives 420/(2.1 × √30) × 16 = 585 mm. With 40 mm clear cover and 100 mm clear spacing, the detailed equation gives about 357 mm, because (cb + Ktr)/db reaches its 2.5 limit.

What is the difference between Table 25.4.2.3 and eq. 25.4.2.4a?

The table is a simplified form that assumes a fixed confinement term for two cover and spacing cases. The equation uses the actual cover and spacing through cb and the transverse steel through Ktr, with (cb + Ktr)/db limited to 2.5, so it usually gives a shorter length.

What does ψg do in ACI 318-19?

ψg is the reinforcement grade factor added in ACI 318-19. It is 1.0 for Grade 280 and 420 bars, 1.15 for Grade 550 and 1.3 for Grade 690, so higher strength bars need proportionally longer development lengths.

When is a bar a top bar?

When more than 300 mm of fresh concrete is cast below the horizontal bar in the member. Bleed water and settlement weaken the bond under such bars, so ψt = 1.3 applies.

How long is a lap splice to ACI 318?

A tension lap is Class A, 1.0 ld, only when the area provided is at least twice that required over the splice and no more than half the bars are spliced there. Otherwise it is Class B, 1.3 ld. Both are at least 300 mm.

Can I print or save the results?

Yes. Print gives a clean report with the inputs, results, working, date and disclaimer. Download PDF creates the same report as a PDF in your browser, and Download CSV gives the figures for a spreadsheet. Nothing is uploaded to our server.

S-901 Contact

Send the drawings. Get an answer from our engineers.

WhatsApp or email the architectural or structural set, the location and what you need. The reply comes from the engineers who will do the work, with a proposed scope and programme.

Office
Al Warqa 1, Dubai, UAE
Hours
Sunday – Thursday, 09:00 – 18:00 GST