1. Home
  2. Tools
  3. Bar bending schedule calculator
Free tool  ·  Indicative  ·  Iron Axis engineering team

Bar bending schedule (BBS) and cutting length calculator

Enter the shape code, bar size and outside dimensions of each bar mark and get the BS 8666:2020 cutting length, the number of bars, the total length and the weight by diameter. Stirrup (link) lengths, U-bars and L-bars include the correct bend deductions, and every number shows its equation.

Engineering disclaimer. This free tool is for preliminary checks and education only. It uses simplified code methods and your inputs, and it is not a substitute for project design. Results must be verified by a qualified structural engineer responsible for the project. Verify every result against the current code edition, national annex, authority requirements and the project drawings before use. Iron Axis accepts no liability for decisions or designs based on these results. Read the full disclaimer.
Bar mark 01 (example: beam bottom U-bars)
Bar mark 02
Bar mark 03
Bar mark 04
Bar mark 05 (optional: set members to 0 to skip)
Bar mark 06 (optional: set members to 0 to skip)
Options
Added to the total weight only. 0 = net.
Warns when a bar is longer.
— total reinforcement bar marks
Step-by-step working

Indicative only. BS 8666 equations at the minimum bend radius; check against the approved drawings and the fabricator’s schedule.

How we calculate

1. Outside dimensions, not centre-line

BS 8666 schedules every bar by its outside dimensions A, B, C… as drawn on the standard shape. Adding them overstates the bar, because each bend is a curve of radius r rather than a sharp corner. The Table 5 length equations deduct an allowance for each bend [1].

2. Length equations used (BS 8666:2020 Table 5)

  • 00 straight: L = A.  11 one bend: L = A + (B) − 0.5r − d.  21 U-bar: L = A + B + (C) − r − 2d.
  • 31 three bends: L = A + B + C + (D) − 1.5r − 3d.  41 four bends: L = A + B + C + D + (E) − 2r − 4d.
  • 51 closed link: L = 2[A + B + (C)] − 2.5r − 5d; with C left at 0 we use the minimised form L = 2A + 2B + max(16d, 160).
  • 63 link lapped on B: L = 2A + 3B + 2(C) − 3r − 6d; minimised form 2A + 3B + max(14d, 140) for bars up to 16 mm and 2A + 3B + 13d for 20 mm and over [1][2].

3. Bend radius and end projections (Table 2)

r is the minimum scheduling radius: 12, 16, 20, 24 and 32 mm for 6 to 16 mm bars (about 2d) and 70, 87, 112, 140 and 175 mm for 20 to 50 mm bars (about 3.5d). We warn when an end leg is shorter than the minimum end projection P (for example 140 mm for H16) or when a link hook is shorter than P for links with end bends under 150° (130 mm for H10, 155 mm for H12) [1][2].

4. Weight

Mass = number of members × bars per member × L × nominal kg/m from BS 4449 (0.395, 0.617, 0.888, 1.579, 2.466, 3.854, 6.313 and 9.864 kg/m for 8 to 40 mm), which is 7,850 kg/m³ × πd²/4 [3]. Totals are grouped by bar size, and the optional wastage percentage is applied to the total weight only.

What a bar bending schedule is

A bar bending schedule (BBS) lists every reinforcing bar in a member: the bar mark, size, shape code, dimensions, number of bars and the cutting length. The fabricator cuts and bends from it, the site checks deliveries against it and the quantity surveyor prices the steel from it. In the UAE and much of the GCC, schedules follow the BS 8666 shape codes, which is what this calculator uses [1].

Cutting length worked examples you can check by hand

  • Stirrup (shape 51), 300 × 500 beam, 25 mm cover, H10: A = 500 − 2 × 25 = 450, B = 300 − 2 × 25 = 250, r = 20 mm. With C = 100 mm, L = 2(450 + 250 + 100) − 2.5 × 20 − 5 × 10 = 1,500 mm. BS 8666 asks for a hook of at least 130 mm for H10 links, so the minimised length is 2 × 450 + 2 × 250 + 160 = 1,560 mm (0.96 kg).
  • U-bar (shape 21), H16, A = 300, B = 5,950, C = 300: r = 32 mm, L = 300 + 5,950 + 300 − 32 − 2 × 16 = 6,486 mm.
  • L-bar (shape 11), H20, A = 1,500, B = 400: r = 70 mm, L = 1,500 + 400 − 0.5 × 70 − 20 = 1,845 mm.
  • Crank (shape 41), H12, 300 / 400 / 500 / 400 / 300: r = 24 mm, L = 1,900 − 2 × 24 − 4 × 12 = 1,804 mm.

Number of bars from spacing

For bars or links at a regular spacing s over a length, the usual count is n = (length to be covered ÷ s) rounded up, plus 1. For example links at 150 mm over 5,700 mm need 5,700 / 150 + 1 = 39 links. Enter that as “bars per member” and the number of identical members as “members”.

BS 8666 or IS 2502 bend deductions?

Many Indian textbooks and site sheets use rounded bend deductions such as 1d for 45°, 2d for 90° and 3d for 135° bends with hook allowances of 9d or 10d. Those are rules of thumb that assume a particular bend radius. BS 8666 ties the deduction to the actual minimum radius for each bar size, so its 90° deduction is 0.5r + d: 2d for bars up to 16 mm, but 2.75d for a 20 mm bar. Use the method your project specification and fabricator follow; this calculator applies BS 8666:2020.

Where the BBS fits in design

Anchorage, laps and bar curtailment come from the design, not from the schedule. Use our development length calculator or lap length calculator to set the straight lengths, the RC beam design calculator to size the bars, and the rebar weight calculator for quick totals. For post-tensioned slabs we schedule the untensioned reinforcement as part of our PT design package and PT shop drawings.

References

The codes and texts the calculator follows, consulted on 20 November 2026. Always use the edition and national annex you will actually rely on.

  1. BSI: BS 8666:2020 Scheduling, dimensioning, cutting and bending of steel reinforcement for concrete. Specification (Table 2 and Table 5)
  2. Collins Reinforcements: BS 8666:2020 shape codes and Table 2 summary sheet
  3. BSI: BS 4449:2005+A3:2016 Steel for the reinforcement of concrete. Weldable reinforcing steel (nominal mass per metre)

Part of our free engineering tools and design guides. Results are for preliminary design and checking, and must be verified by a qualified structural engineer responsible for the project. Clauses are referred to where we are confident of the reference; always check the edition and national annex adopted for your project.

S-701 FAQ

Questions we are asked about this.

How do you calculate the cutting length of a stirrup?

For a BS 8666 shape 51 closed link, L = 2(A + B + C) − 2.5r − 5d, where A and B are the outside dimensions (member size minus twice the cover) and C is the hook. With the minimum hook, L = 2A + 2B + max(16d, 160). A 300 × 500 beam with 25 mm cover and H10 links gives 2 × 450 + 2 × 250 + 160 = 1,560 mm.

What is the bend deduction for a 90° bend?

BS 8666 deducts 0.5r + d per 90° bend, with r the minimum scheduling radius. That is 2d for bars up to 16 mm (r = 2d) and 2.75d for 20 mm and larger bars (r = 3.5d), for example 24 mm for H12 and 55 mm for H20.

What does the dimension in brackets mean on a shape code?

It is the free dimension. The fabricator lets that leg take up the cutting and bending tolerance, so it is the least critical one. Put the critical dimension elsewhere.

What is the minimum leg length for a bent bar?

BS 8666 Table 2 gives the minimum end projection P: 120 mm for H10, 125 mm for H12, 140 mm for H16, 190 mm for H20 and 235 mm for H25. Links with hooks bent less than 150° need more: 130 mm for H10 and 155 mm for H12.

How do I calculate the weight of bars in a BBS?

Weight = number of bars × cutting length (m) × kg/m. The kg/m of a bar is d²/162 or, more precisely, the BS 4449 value: 0.617 for 10 mm, 0.888 for 12 mm, 1.579 for 16 mm, 2.466 for 20 mm and 3.854 for 25 mm.

Does the calculator add laps and anchorage lengths?

No. Laps, anchorages and curtailment come from the design and drawings. Enter the dimensions that already include them; the calculator then works out the cut length and warns when a bar is longer than the stock length.

S-901 Contact

Send the drawings. Get an answer from our engineers.

WhatsApp or email the architectural or structural set, the location and what you need. The reply comes from the engineers who will do the work, with a proposed scope and programme.

Office
Al Warqa 1, Dubai, UAE
Hours
Sunday – Thursday, 09:00 – 18:00 GST