1. Home
  2. Resources
  3. PT transfer slabs and beams
PT design guide  ·  Iron Axis engineering team

Post-tensioned transfer slabs and transfer beams: a design guide

Transfer structures carry columns and walls from a tower down onto a different grid below. Post-tensioning makes them thinner and stiffer, but adds staged stressing, deep-beam behaviour and mass-concrete issues. How we approach each step.

Design codes
ACI 318 · Eurocode 2 · PTI
Software
RAM Concept · AutoCAD · Revit

Towers in Dubai, Abu Dhabi, Riyadh and Jeddah often sit on podiums with a different column grid: retail, car parks or ballrooms below, apartments or hotel rooms above. The structure that changes the grid, a transfer slab or a set of transfer beams, carries some of the largest forces in the building. Post-tensioning lets that structure be shallower and stiffer, which saves storey height and controls deflection of the floors above. This guide sets out the design steps. For the scope we provide, see our PT transfer slab and beam design service.

Transfer slab or transfer beams?

  • Transfer beams (girders) pick up a few heavy columns along defined lines. They are efficient where the grid offsets are regular, and the slab between them can be a normal PT floor.
  • Transfer slabs, often 1.5 to 3 m thick, are used where columns above land randomly on the grid below. They are simpler to form but use more concrete and create mass-pour issues.
  • Hybrid schemes use thickened bands or local deep beams within a slab.

The choice depends on the architecture, storey height, construction sequence and cost. We usually compare options in the preliminary design stage.

Load balancing for concentrated loads

For a column load at a point, a harped (draped to a sharp low point) tendon is more efficient than a parabola. A tendon with force P that drops by a over a length L/2 to a low point under the load pushes upward with:

Fup ≈ 2 P sinθ ≈ 4 P a / L    (small angles, low point at midspan)

In practice the low point is a short curve with the system's minimum radius, and multistrand bonded tendons in ducts are used because of the forces involved. The tendons balance part of the column loads; the rest is carried by bending with bonded reinforcement.

Staged stressing

A transfer element is loaded gradually as the floors above are built. If all the prestress were applied at the start, the upward force would far exceed the self-weight and the element would hog and crack on top. The usual solution is to stress in stages:

  1. Stage 1: enough prestress to carry self-weight and the first few floors, while satisfying transfer stresses (see transfer stress checks).
  2. Further stages as floors are added, each checked for stresses at the current load.
  3. Final stage when most of the permanent load is in place.

The stressing sequence and the floor counts at which each stage happens go on the drawings and must be coordinated with the contractor's programme. Propping beneath the transfer element and load sharing with the floors below during construction also need checking.

Worked example: harped transfer beam (illustrative)

A simply supported transfer beam, span 12 m, carries one column at midspan with a final service load of 6,000 kN, and its own weight of about 60 kN/m. Target: balance about 70 percent of the column load. Available drape a = 1.0 m.

Fup = 0.7 × 6000 = 4,200 kN    →    P = Fup L / (4a) = 4200 × 12 / (4 × 1.0) = 12,600 kN effective

That is roughly 90 to 100 strands of 15.2 mm at typical effective forces, arranged in several multistrand tendons. At stage 1, with only the beam self-weight (about 720 kN in total) and perhaps two floors acting, the full force would give a net upward load of several thousand kN, so stage 1 might stress about a third of the tendons, with the rest stressed as the floors go up. The beam is then checked as a deep member (below).

Indicative values. Strand forces, stage proportions and dimensions are illustrative only. Every transfer structure needs its own sequence analysis.

Deep beams and strut-and-tie

Many transfer beams and slabs are deep relative to their span. ACI 318-19 §9.9 defines deep beams (clear span not more than four times the depth, or concentrated loads within twice the depth of the support) and requires non-linear strain distribution to be considered, usually by the strut-and-tie method of Chapter 23. EN 1992-1-1 §5.6.4 and §6.5 provide the equivalent strut-and-tie rules. Key checks:

  • Nodal zones under the columns above and over the supports below, with bearing stress limits.
  • Struts from the column load to the supports; the tendon and bonded reinforcement act as ties.
  • Minimum distributed reinforcement in both faces (ACI 318-19 §9.9.3.1).
  • Anchorage zones of multistrand tendons, which are large in transfer beams (see anchorage zones and bursting).
  • Punching of heavy columns into transfer slabs (see punching shear).

Deflection and stiffness

The deflection of a transfer structure shows up in every floor above it, as cracks in partitions and façades. Authorities therefore set tighter limits. For example, the Sharjah Municipality regulations give a transfer slab deflection limit of span/800, and the Ras Al Khaimah structural regulations give span/750 for transfer elements. Long-term deflection includes creep under the sustained load and the construction load history (see long-term deflection). The tower analysis should include the transfer element's flexibility, because it redistributes load between columns above.

Mass concrete and thermal control

A 2 to 3 m thick transfer slab poured in Gulf conditions can reach high core temperatures from hydration. Large differences between the core and the surface cause early thermal cracking, and very high peak temperatures can risk delayed ettringite formation. Typical measures include low-heat mixes with slag or fly ash, chilled water or ice, night pours, insulation, thermocouples, and pour sequencing. Early partial stressing also helps control early-age cracking. See temperature and restraint cracking.

Coordination checklist

  • Column and wall loads above, with their construction sequence.
  • Tendon layout clear of column starter bars, MEP sleeves and large openings (see openings and penetrations).
  • Stressing access: pockets and jacking clearance at the ends, sometimes from a temporary platform.
  • Grouting procedure and testing for bonded tendons.
  • Fire resistance of the transfer element, which often needs the highest rating in the building (see fire resistance of PT slabs).

Summary

PT transfer structures: key checks
ItemRule or practiceReference
Balancing a column loadHarped tendon, Fup ≈ 4Pa/LMechanics
Staged stressingStress in steps with the load; check each stageDesign practice; transfer stress limits
Deep beam definitionln ≤ 4h, or load within 2h of supportACI 318-19 §9.9.1.1
Design methodStrut-and-tieACI 318-19 Ch. 23; EN 1992-1-1 §6.5
Deflection limitsSpan/800 (Sharjah), span/750 (RAK) for transfer elementsAuthority regulations
Mass poursThermal control plan, temperature monitoringProject specification

Part of our PT design guides. Codes are referred to by clause where we are confident of the reference, and coefficients marked indicative should be checked against the code text; always check the edition and national annex adopted for your project. Worked examples are illustrative, not designs.

S-426 FAQ

Questions we are asked about this.

Why use post-tensioning for transfer structures?

Prestress balances a large part of the column loads, so the transfer slab or beam can be shallower and stiffer, which saves storey height and limits the deflection felt by the floors above.

What is staged stressing?

Applying the prestress in steps as the floors above are built, so that the upward force never greatly exceeds the load present at the time.

Are transfer beams designed as deep beams?

Often. ACI 318-19 §9.9 treats beams with clear span up to four times the depth, or with concentrated loads near the supports, as deep beams, usually designed by strut-and-tie.

What deflection limits apply to transfer slabs in the UAE?

Authority rules vary. The Sharjah regulations give span/800 for transfer slabs and the Ras Al Khaimah regulations give span/750 for transfer elements. Project criteria may be stricter.

How is cracking controlled in a thick transfer slab pour?

With a thermal control plan: low-heat mixes, cooling, insulation, temperature monitoring, pour sequencing and early partial stressing.

Can you design a PT transfer slab for our tower?

Yes. Our PT transfer slab and beam design service covers scheme comparison, tendon layout, staged stressing, strut-and-tie checks and drawings.

S-901 Contact

Send the drawings. Get an answer from our engineers.

WhatsApp or email the architectural or structural set, the location and what you need. The reply comes from the engineers who will do the work, with a proposed scope and programme.

Office
Al Warqa 1, Dubai, UAE
Hours
Sunday – Thursday, 09:00 – 18:00 GST