1. Home
  2. Tools
  3. Block calculator
Free tool  ·  Indicative  ·  Iron Axis engineering team

Block calculator: blocks per m², mortar, cement and sand

Find how many blocks or bricks you need for a wall: units per m², the total after openings and wastage, and the mortar, cement bags and sand for your mix. Choose a standard 400 × 200 block, a UK block, an 8 in CMU or a brick, or enter your own size.

Engineering disclaimer. This free tool is for preliminary checks and education only. It uses simplified code methods and your inputs, and it is not a substitute for project design. Results must be verified by a qualified structural engineer responsible for the project. Verify every result against the current code edition, national annex, authority requirements and the project drawings before use. Iron Axis accepts no liability for decisions or designs based on these results. Read the full disclaimer.
Block or brick
5% typical for blocks, 5–10% for bricks.
Wall
Doors and windows.
Mortar
e.g. 1:4, 1:5 or 1:6.
— blocks to order
Step-by-step working

Indicative only. Quantities for estimating; follow the masonry specification for the mix and units.

How we calculate

1. Units

  • Units per m² = 1 / [(L + j)(H + j)] with the face length L, face height H and joint j. A 400 × 200 block with 10 mm joints gives 1/(0.41 × 0.21) = 11.61 per m².
  • Units in the wall = per m² × (length × height − openings), then × (1 + wastage), rounded up.

2. Mortar

  • Solid units and bricks: full bed and head joints, mortar = wall volume − volume of the units.
  • Hollow units: face-shell bedding, as in TMS 402/602 and common practice for hollow blocks: two strips, each about 0.35 × thickness wide, in the bed and head joints [1].

3. Cement and sand

  • Dry volume = wet mortar × dry-volume factor (1.27 to 1.33 is the usual allowance for voids and bulking). Cement = dry volume / (1 + n) × 1,440 kg/m³; sand = dry volume × n / (1 + n).

How many blocks per m²?

Units per m² with 10 mm joints
UnitFace size (mm)Per m²
Block 400 × 200 (100, 150, 200, 250 thick)400 × 20011.61
UK block440 × 2159.88
CMU 8 in (nominal 16 × 8 in)397 × 194 (with 9.5 mm joints)about 12.1
UK brick, half-brick wall215 × 6559.3
Modular brick, half-brick wall190 × 9050.0

The face size, not the thickness, sets the count per m². Thickness changes the mortar and the weight.

Worked example

A 10 m long, 3 m high wall of 200 mm hollow blocks (400 × 200 face) with 2 m² of openings and 10 mm joints:

  • Net area = 30 − 2 = 28 m²; 11.61 × 28 = 325.2 blocks; with 5% wastage, order 342.
  • Face-shell mortar ≈ 0.28 m³ wet, 0.375 m³ dry. In a 1:6 mix that is about 77 kg of cement (1.5 bags of 50 kg) and 0.32 m³ of sand.

The same wall in 100 mm solid blocks takes the same 342 blocks and about 0.20 m³ of wet mortar.

Good practice

  • Order blocks by the pallet and keep a few spares of the same batch for cutting and breakages.
  • Mix, joint thickness and reinforcement (bed-joint mesh, lintels, ties to columns) come from the specification and the structural drawings.
  • Masonry walls on slabs add load: about 2 to 4 kN/m² of wall face for 100–200 mm block walls with plaster. Allow for them in the slab load calculator.

For concrete quantities see our concrete volume calculator; for plaster and paint, the paint calculator.

References

The codes and texts the calculator follows, consulted on 19 November 2026. Always use the edition and national annex you will actually rely on.

  1. TMS: TMS 402/602 Building Code Requirements and Specification for Masonry Structures (face-shell bedding of hollow units)

Part of our free engineering tools and design guides. Results are for preliminary design and checking, and must be verified by a qualified structural engineer responsible for the project. Clauses are referred to where we are confident of the reference; always check the edition and national annex adopted for your project.

S-791 FAQ

Questions we are asked about this.

How many blocks are in 1 m²?

For a 400 × 200 mm block with 10 mm joints, 11.61 per m² (1 / (0.41 × 0.21)). Ignoring the joints gives 12.5 per m², a figure some estimators use as a built-in allowance for cuts.

How many bricks are in 1 m² of wall?

About 59 standard UK bricks (215 × 65 face, 10 mm joints) in a half-brick wall, and double that in a one-brick wall. For 190 × 90 modular bricks about 50 per m².

How much cement do I need for blockwork?

For 200 mm hollow blocks laid on face-shell bedding in a 1:6 mix, roughly 2.7 kg of cement per m² of wall; solid 100 mm blocks take a little less mortar per m². The calculator works it out for your wall.

What is the dry volume factor?

Mortar shrinks when mixed because the cement and water fill the voids in the sand. Multiplying the wet volume by 1.27 to 1.33 gives the dry volume of materials to buy.

What wastage should I allow for blocks?

About 5% for blocks and 5 to 10% for bricks, more for walls with many openings or cuts.

Does wall thickness change the number of blocks?

No, only the face size and the joint do. A 100 mm and a 200 mm block wall with the same 400 × 200 face need the same number of blocks per m².

S-901 Contact

Send the drawings. Get an answer from our engineers.

WhatsApp or email the architectural or structural set, the location and what you need. The reply comes from the engineers who will do the work, with a proposed scope and programme.

Office
Al Warqa 1, Dubai, UAE
Hours
Sunday – Thursday, 09:00 – 18:00 GST